EUROLOGIC Voyager 3000 Guía de instalación Pagina 163
- Pagina / 178
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
HP-UX version 11.00.03 B-1
B
Updating PROM Code B-
This appendix describes how to update the different PROM codes and download I/O
firmware.
Updating PROM Code
All new or replacement boards come with the latest PROM code already installed.
However, occasionally circumstances might require that you update the PROM on
new hardware. In addition, Stratus releases revisions to PROM code periodically that
must be copied to (or burned on) your existing boards.
WARNING
Do not update PROM code yourself unless a Stratus representative
instructs you to do so. Improperly updating PROM code can damage a
board and interrupt system services. If you are not sure which PROM
code file you need to burn, contact the CAC. Also, do not attempt to
update CPU/memory PROM code if you are running with only one CPU
board.
The following sections describe how to update PROM code on CPU/memory boards,
console controllers, and SCSI adapter cards. Before you begin updating the PROM
code, you must determine which PROM file you need to burn. PROM code files are
located in the /etc/stratus/prom_code directory. Table B-1 describes the PROM
code file naming conventions.
- HP-UX Operating System: 1
- Contents 3
- Revision Information 13
- Audience 13
- Notation Conventions 13
- Product Documentation 16
- Online Documentation 17
- Related Documentation 18
- Ordering Documentation 19
- Commenting on This Guide 19
- Getting Started 1 21
- Using This Manual 22
- Console Controller 25
- Fault Tolerant Design 26
- Duplexed Components 27
- Solo Components 28
- Setting Up the System 2 29
- Installing a System 30
- Configuring a System 30
- Maintaining a System 33
- Overview of the Boot Process 35
- Modifying CONF Variables 40
- Sample CONF Files 41
- Modifying the CONF File 42
- Booting Process Commands 43
- CPU PROM Commands 44
- Primary Bootloader Commands 45
- Booting the System 50
- Issuing Console Commands 51
- <Return> 52
- Manually Booting Your System 53
- <Return> to continue 55
- Shutting Down the System 57
- Using SAM 58
- Using Shell Commands 58
- Changing to Single-User State 59
- Rebooting the System 59
- Halting the System 60
- Activating a New Kernel 61
- Dealing with Power Failures 63
- Managing Flash Cards 65
- Flash Card Utility Commands 66
- Creating a New Flash Card 68
- Duplicating a Flash Card 68
- Mirroring Data 4 69
- Sample Mirror Configuration 71
- Recommended Volume Structure 71
- HP-UX version 11.00.03 5-1 79
- Using Hardware Utilities 80
- Determining Hardware Paths 80
- I/O Subsystem Paths 86
- ■ the logical cabinet 87
- ■ the logical CPU/memory 87
- Defining a Logical SCSI Bus 93
- Determining Component Status 100
- Software State 101
- Hardware Status 103
- Managing Hardware Devices 104
- Error Detection and Handling 105
- Disabling a Hardware Device 106
- Enabling a Hardware Device 106
- Correcting the Error State 106
- Managing MTBF Statistics 107
- Displaying MTBF Information 108
- Clearing the MTBF 108
- Changing the MTBF Threshold 109
- Error Notification 110
- Remote Service Network 111
- Status Lights 111
- Console and syslog Messages 112
- Status Messages 112
- Analyzing System Status 112
- Modifying System Resources 113
- Fault Codes 114
- Saving Memory Dumps 119
- Space Issues 120
- Configuring save_mcore 123
- Configuration 125
- Kernel Configuration area 125
- Analyzing the Dumps 129
- Preventing the Loss of a Dump 130
- Remote Service Network 6 131
- How the RSN Software Works 132
- Using the RSN Software 134
- Starting the RSN Software 135
- Checking Your RSN Setup 136
- Stopping the RSN Software 137
- Sending Mail to the HUB 138
- Validating Incoming Calls 139
- Testing the RSN Connection 139
- Listing RSN Requests 139
- Cancelling an RSN Request 140
- RSN Command Summary 141
- RSN Files and Directories 142
- Communication Queues 143
- Other RSN-Related Files 145
- Remote STREAMS Environment 7 147
- Configuring the Host 149
- Remote STREAMS Environment 150
- Customizing the orsdinfo File 152
- Downloading Firmware 153
- Adding or Moving a Card 155
- New and Customized Software 159
- Console Interface 160
- Flash Cards 160
- Remote Service Network (RSN) 161
- New and Customized Commands 162
- Updating PROM Code B 163
- Updating PROM Code 163
- Updating CPU/Memory PROM Code 165
- Downloading I/O Card Firmware 172
- IndexIndex 173
Relacionado con productos y manuales para Redes EUROLOGIC Voyager 3000
Redes EUROLOGIC Voyager 3000 Manual de usuario
(74 paginas)
(74 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.136 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales